GETTING FAMILIAR WITH PLUMBING: A MUST FOR INSTALLING A BATHTUB

Getting Familiar with Plumbing: A Must for Installing a Bathtub

Getting Familiar with Plumbing: A Must for Installing a Bathtub

Blog Article

Click Here

The content in the next paragraphs on the subject of How to Install a Bathtub: Install an Acrylic Tub and Tub Surround is unquestionably entertaining. Read it for your own benefit and see what you think of it.


A Step-by-Step Guide to Installing a Bathtub
Installing a bathtub isn't precisely brain surgery, but it does need strong plumbing, woodworking, as well as in some cases, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a moderately tough job. If the old bathtub is conveniently accessible, the task can relocate speedily; if you need to open up a wall surface to remove the old bathtub as well as position the brand-new bathtub, the job is a lot harder. In either case, the task is within a home handyman's abilities, although you will need an assistant to move out the old tub and set in the new one. Make certain you have qualified yourself for the job as well as fit trying it. Instead of working with a professional to take over a halfway-completed project, it is much better to think about utilizing one prior to you start. Opportunities are you may require a specialist plumber to make tube links.
This write-up will help you set up a new bath tub in your restroom if you have already bought a new bathtub and also don't require to alter the plan of your previous water system pipes.
Your tools as well as product list ought to comprise the following:
  • New Bath tub

  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Knife

  • Tape Measure

  • Pipeline Caps


  • Removing Old Taps


    If you require to replace old faucets with brand-new ones as a part of your installment, after that the first thing you need to do is disconnect the water system. After doing so, activate the faucets to drain pipes any type of water staying in the system. The process of getting rid of the existing faucets can be rather troublesome because of the restricted access that is typically the situation.
    Use a container wrench (crowsfoot spanner) or a tap tool to undo the nut that attaches the supply pipes to the faucets. Have a fabric all set for the staying water that will certainly originate from the pipes. Once the supply pipes have actually been eliminated, utilize the same device to loosen the nut that holds the taps onto the bath/basin. You will require to quit the single faucets from transforming during this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will have to be cleaned up of any old securing compound.
    Prior to carrying on to fit the new taps, compare the pipeline connections on the old faucets to the brand-new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the brand-new taps to fit.

    Suitable New Touches


    If the tails of the brand-new taps are plastic, after that you will need a plastic port to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and also the various other end gives a link to the existing supply pipes.
    If you require to fit a monobloc, then you will need lowering couplers, which links the 10mm pipeline of the monobloc to the common 15mm supply pipe.
    Next, position the faucet in the installing hole in the bath/basin ensuring that the washing machines are in area in between the tap as well as the sink. Protect the faucet in position with the producer supplied backnut. Once the faucet is safely in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with normal faucet connectors. The former kind needs to be linked to the tap finishes initially, tightening only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have been attached.

    Mounting the Bathtub


    Making use of the two wood boards under its feet, place the bathtub in the required placement. The wood boards are useful in equally spreading out the weight of the tub over the area of the boards as opposed to concentrating all the weight onto four little points.
    The following goal is to make certain that the bathtub is leveled all round. This can be accomplished by examining the level as well as changing the feet on the tub until the spirit level reads degree.
    To set up faucets, fit all-time low of the furthest versatile tap port to the appropriate supply pipeline by making a compression sign up with; then do the very same for the other faucet.
    Activate the water system and examine all joints and also brand-new pipework for leaks and tighten them if necessary. Load the bathtub and also examine the overflow electrical outlet as well as the normal electrical outlet for leakages.
    Ultimately, fix the bathroom paneling as defined in the supplier's instruction manual. Tiling as well as sealing around the bath tub needs to wait till the bath tub has been utilized at least when as this will certainly settle it into its final setting.

    Planning for the Installation


    To start with, the supporting framework provided with the bathroom ought to be fitted (if needed) according to the manufacturer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is necessary to ensure that if the faucet features a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is likewise practical to fit a sustaining plate under the taps system to stop pressure on the tub.
    Fit the versatile tap connectors to the bottom of the two faucets utilizing 2 nuts and olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipeline.
    Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Ensure you utilize every one of the provided washers.
    Link the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Connect the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its final placement.

    Tiling Around the Tub


    In the area where the bathroom fulfills the ceramic tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the installation can relocate enough to fracture a stiff seal, creating the water to pass through the wall in between the bathroom and the tiling, bring about difficulties with wetness as well as possible leaks to the ceiling below.
    You can choose from a range of coloured sealants to assimilate your components as well as fittings. They are offered in tubes as well as cartridges, and also can securing gaps approximately a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of soaked paper or soft rope. Bear in mind to constantly fill the bathtub with water prior to sealing, to enable the activity experienced when the bathtub is in usage. The sealant can fracture fairly early if you do not think about this activity prior to securing.
    Alternatively, ceramic coving or quadrant ceramic tiles can be utilized to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to size, are additionally easily readily available on the market. It is advisable to fit the ceramic tiles making use of waterproof or water resistant glue and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub: Install an Acrylic Tub and Tub Surround

    We hope you enjoyed our topic about How to Install a Bathtub Yourself. Thank you for taking the time to read through our article post. Please take the time to distribute this write-up if you liked it. We love reading our article about How to Install a Bathtub.


    Act fast, call!

    Report this page